University of Surrey

Test tubes in the lab Research in the ATI Dance Research

Improvement in current carrying capability of spray deposited silver nanowire transparent conducting.

Fantanas, Dimitrios (2019) Improvement in current carrying capability of spray deposited silver nanowire transparent conducting. Doctoral thesis, University of Surrey.

[img] Text (Thesis)
Improvement in current carrying capability of spray deposited silver nanowire transparent conducting - EngD Thesis - Dimitrios Fantanas.pdf - Version of Record
Restricted to Repository staff only until 31 July 2022.
Available under License Creative Commons Attribution Non-commercial Share Alike.

Download (95MB)
[img] Text (Restriction Approval)
Restriction - Dimitrios Fantanas - EngD Thesis.pdf
Restricted to Repository staff only
Available under License Creative Commons Attribution Non-commercial Share Alike.

Download (801kB)

Abstract

Silver Nanowires (Ag NWs) are a heavily researched material, mostly as a replace-ment for the industry standard Indium Tin Oxide (ITO). Ag NWs are sought after be-cause they can be used on flexible substrates and be solution deposited. One main drawback of silver NWs is the film failure during either electrostatic discharge (ESD) tests or direct Joule heating, at currents significantly lower than ITO can handle. In this work the up scaling of the spray deposition of Ag NWs and the current induced failure that is observed during film use in electronic devices are investigated. Both of these areas are ones of the few stopping Ag NWs from being adopted by the industry. As part of this project, a holistic approach is taken, where a machine for the deposition was designed and tuned to improve the efficiency of the process, then using that tool process devel-opment was undertaken using various dispersions and finally the current induced failure of the deposited films was investigated. This way a complete understanding was achieved of the spray process and of silver nanowires as a material.

Using a spray deposition tool, built and commissioned during the project, the indus-try requirements of less than 10% uniformity variation, optical transmission over 90% and haze bellow 1% were achieved for 150 mm width at 100 Ω/sq. Furthermore, better understanding of the spray pattern and nozzle overlap was achieved using experimental and simulation data. Based on this tool and the knowledge acquired from its design, a series of customer machines were designed for various applications. The original tool was upgraded to an airbrush-based system, in order to facilitate for R&D work such as process development and sample preparation for small scale application tests. Various nanowire dispersions were tested from various suppliers using this upgraded tool with success. Using the fine-tuned process, films were deposited for solar cells, liquid crystal displays, light emitting diodes and heaters, with great preliminary results. Finally, the deposition of nanowires on 3D surfaces was achieved with great success.

To understand the current induced failures, the failure mechanism and the maximum current density that the nanowires can withstand needs to be identified. To do that, small scale tests were undertaken and then the films were imaged using SEM and AFM. From these measurements it was found that the maximum current density (18-260 MA/cm2), at which the NW films fail, is much lower than what has been observed in lit-erature (18-260 MA/cm2). As part of this work it was found that for a 100 Ω/sq film, the failure occurred at a current density of 7 MA/cm2. This is because of the Joule heating of the nanowires, which in the case of dense networks initiates in the junctions. This is be-cause the junction resistance dominates over the resistance of the individual wires, since it is an order of magnitude higher. It was found that denser nanowire networks (lower sheet resistance), fail at lower current densities. This is because the number and the prox-imity of the junctions increase, resulting in quicker heating and failure. Furthermore, when network is consisted of multiple layers of nanowires, the heat dissipates at a slow-er rate, since the top nanowires have just air for the heat to be transferred to, in contrast with the bottom layer wires, which dissipate heat through direct contact with the glass substrates (better heat conductor than air). The failure is always in a line, perpendicular to the current flow. This is happening because the film failure originates from a weak spot of the sample. This weak spot is on an axis perpendicular to the current flow where there is a less dense patch of the film. When one junction fails, more current has to pass through a smaller number of nanowires, resulting in a chain reaction. Various treatments and NW hybrid materials are proposed in order to decrease the succeptability to the cur-rent induced failure resistance of the films. Two of them are the incorporation of gra-phene on the junctions, which acts as a heat sink and the introduction of a PEDOT:PSS film, which acts as a larger area for the heat to dissipate through and also, creates more channels for the current to flow through.

Item Type: Thesis (Doctoral)
Divisions : Theses
Authors :
NameEmailORCID
Fantanas, Dimitrioshttps://orcid.org/0000-0002-4068-123X
Date : 31 July 2019
Funders : Engineering and Physical Sciences Research Council (EPSRC)
DOI : 10.15126/thesis.00852001
Contributors :
ContributionNameEmailORCID
http://www.loc.gov/loc.terms/relators/THSDorey, Robertr.dorey@surrey.ac.uk
http://www.loc.gov/loc.terms/relators/THSHenley, SimonS.Henley@surrey.ac.uk
http://www.loc.gov/loc.terms/relators/THSShkunov, MaximM.Shkunov@surrey.ac.uk
Depositing User : Dimitrios Fantanas
Date Deposited : 02 Aug 2019 08:15
Last Modified : 02 Aug 2019 08:16
URI: http://epubs.surrey.ac.uk/id/eprint/852001

Actions (login required)

View Item View Item

Downloads

Downloads per month over past year


Information about this web site

© The University of Surrey, Guildford, Surrey, GU2 7XH, United Kingdom.
+44 (0)1483 300800